Arduino Pro 328 – 3.3V/8MHz

Опубликовано автор admin

Features:

  • ATmega328 running at 8MHz external resonator (select ‘Arduino Duemilanove w/ 328’ within the Arduino software).
  • Low-voltage board needs no interfacing circuitry to popular 3.3V devices and modules (GPS, Accelerometers, sensors, etc)
  • USB connection off board
  • 3.3V regulator
  • Max 150mA output
  • Over current protected
  • Reverse polarity protected
  • DC input 3.3V up to 12V
  • Resettable fuse prevents damage to board in case of short
  • Power select switch acts as on/off switch

Dimensions: 2.1×2.05″ (53.34×52.08mm)

Documents:

Triple Axis Accelerometer Breakout – MMA8452Q

Опубликовано автор admin

Features:

  • 1.95 V to 3.6 V supply voltage
  • 1.6 V to 3.6 V interface voltage
  • ±2g/±4g/±8g dynamically selectable full-scale
  • Output Data Rates (ODR) from 1.56 Hz to 800 Hz
  • 12-bit and 8-bit digital output
  • I2C digital output interface (operates to 2.25 MHz with 4.7 kΩ pullup)
  • Two programmable interrupt pins for six interrupt sources
  • Three embedded channels of motion detection
  • Orientation (Portrait/Landscape) detection with set hysteresis
  • High Pass Filter Data available real-time
  • Current Consumption: 6 μA – 165 μA

Documents:

SBC8018 AM1808 Single Board Computer

Опубликовано автор admin
  • 375MHz TI AM1808 ARM926 Microprocessor
  • Onboard 128MByte DDR SDRAM + 128MByte NAND Flash
  • UART, USB, Ethernet, LCD/TSP, SATA, Camera, Audio, TF, JTAG,…
  • Optional WiFi, Camera and 3G Modules
  • Ready-to-Run Linux2.6.33 and WinCE 6.0 OS


Hardware Features

Mechanical Parameters

  • Dimensions: 112.24mm x 82.29mm
  • Working temperature: 0~70 Celsius
  • Input Voltage: +5V
  • Humidity Range: 20% ~ 90%
  • Power Consumption: 0.22A @ 5V (working without LCD)

Processor

  • TI AM1808 ARM9 microprocessor
    – 375-MHz ARM926EJ-S RISC MPU, also supports 456MHz operation
    – ARM926EJ-S Core
    – ARM9 Memory Architecture
    – Enhanced Direct-Memory-Access Controller 3 (EDMA3)
    – 128K-Byte On-chip Memory
    – 1.8V or 3.3V LVCMOS IOs (except for USB and DDR2 interfaces)
    – Two External Memory Interfaces
    – Three Configurable 16550 type UART Modules
    – LCD Controller
    – Two Serial Peripheral Interfaces (SPI) Each With Multiple Chip-Selects
    – Two MMC/SD Card Interface with Secure Data I/O (SDIO) Interfaces

Memory

  • 128MByte Mobile DDR SDRAM
  • 128MByte NAND Flash (on the rear of the board)

Audio/Video Interfaces

  • Audio input interface (Mic In)
  • Two-channel Audio output interface (Line Out)
  • Two Camera interfaces (30-pin FPC connector on the rear of the board, supports CCD or CMOS camera)
  • LCD/Touch Screen interface (50-pin FPC connector, support resolution up to 2048*2048)

Data Transfer Interfaces and Other Facilities

  • 1 x 5 line Debug serial port, RS232 voltage (brings out by DB9 connector)
  • 2 x 3 line serial ports, TTL voltage (brings out by extension connector)
  • 1 x USB2.0 OTG port, High-speed (Mini USB type)
  • 1 x USB1.1 Host port, Full-speed (USB-A type)
  • 1 x TF card slot
  • 1 x Serial ATA connector, supports both SATA I (1.5 Gbps) and SATA II (3.0 Gbps)
  • 1 x 10/100Mbps Ethernet interface (RJ45 connector)
  • Battery backed RTC (User needs to prepare battery himself, CR1220 model is ok)
  • 1 x RESET button
  • 1 x BACK button
  • 1 x HOME button
  • 1 x MENU button
  • 1 x 14-pin JTAG connector (for using TI’s XDS100v2 Emulator)
  • 2 x 40-pin extension connectors (SPI, I2C, McBSP, UART, 1.8V, 3.3V, 5V, GPIO are brought out from these connectors)

  • Полное описание
  • SBC8018 (PDF)
  • Купить

WT21 Bluetooth HCI module

Опубликовано автор admin

WT21 is intended at Bluetooth applications where a host processor is capable of running the Bluetooth software stack. WT21 only implements the low level Bluetooth Host Controller Interface (HCI) but still offers advantages of a module – easy implementation and certifications.

Key Features:

  • Highly integrated and cost effective Bluetooth HCI module
  • Bluetooth class 1 radio based on CSR’s BlueCore-6
  • Transmit power 6dBm, receiver sensitivity -87dB
  • Integrated antenna or RF pin
  • Small size: 17,1 x 11,6 x 2,6mm
  • Bluetooth 2.1 + EDR Compliant
  • Bluetooth controller subsystem CE, FCC and IC qualified
  • Industrial temperature range from -40C to +85C
  • 801.11 co-existence interface
  • AuriStream baseband codec, which provides better audio quality
  • Supports any Bluetooth stack with HCI interface

Description

WT21 is intendend for Bluetooth applications where a host processor is capable of running the Bluetooth software stack. WT21 only implements the low level Bluetooth Host Controller Interface (HCI) but still offers advantages of a module- easy implementation and certifications. WT21 is based on CSR’s BlueCore-6 chip and offers the lowest current consumption and the highest integration level in its class. WT21 supports Bluetooth 2.1 + EDR standard. It also has AudiStream technology built in, which significantly improves the quality of voicein audio applications.

WT21 supports any Bluetooth software stack that implements the standard Bluetooth HCI interface. The software stack can interface to the module either via UART, SDIO or SPI interface. WT21 offers Bluetooth
in integrated form factor that is easy to understand, manage and source. It is an ideal product for an OEM who does not want to spend significant amount of time and money to RF regulatory approvals and designing a complex 2,4 GHz radio product. By utilizing Bluegiga’s world-class integration services and technical support, OEMs can beassured that their products reach the market quickly and cost efficiently.

http://www.bluegiga.com/WT21_Bluetooth_HCI_Module