STEVAL-MKI062V2 (iNEMO)

Опубликовано автор admin

 

  • Two power supply options: power connector, USB connector
  • STM32F103RE: high-density performance line ARM-based 32-bit MCU with 256 to 512 kB Flash, USB, CAN, 11 timers, 3 ADCs and 13 communication interfaces
  • LPR430AL: 2-axis gyro (roll, pitch) 300°/s full scale with analog output and optional additional filters
  • LY330ALH: yaw-axis gyro 300°/s full scale with analog output and optional additional filters
  • LSM303DLH: 6-axis geomagnetic module: ±2 g / ±4 g / ±8 g linear acceleration full scale, magnetic field configurable full scale ±1.3 to ± 8.1 Gauss (max), I2C digital output
  • LPS001DL: pressure sensor 300-1100 mbar absolute full scale with I2C digital output and barometer
  • STLM75: temperature sensor with –55 to +125°C range and I2C digital interface
  • Extended connector for wireless connectivity
  • MicroSD™ card slot
  • COM connector with RTS and CTS signals
  • USB 2.0 full speed connection
  • Reset button
  • User LED and button
  • RoHS Compliant

Arduino Pro 328 – 3.3V/8MHz

Опубликовано автор admin

Features:

  • ATmega328 running at 8MHz external resonator (select ‘Arduino Duemilanove w/ 328’ within the Arduino software).
  • Low-voltage board needs no interfacing circuitry to popular 3.3V devices and modules (GPS, Accelerometers, sensors, etc)
  • USB connection off board
  • 3.3V regulator
  • Max 150mA output
  • Over current protected
  • Reverse polarity protected
  • DC input 3.3V up to 12V
  • Resettable fuse prevents damage to board in case of short
  • Power select switch acts as on/off switch

Dimensions: 2.1×2.05″ (53.34×52.08mm)

Documents:

Triple Axis Accelerometer Breakout – MMA8452Q

Опубликовано автор admin

Features:

  • 1.95 V to 3.6 V supply voltage
  • 1.6 V to 3.6 V interface voltage
  • ±2g/±4g/±8g dynamically selectable full-scale
  • Output Data Rates (ODR) from 1.56 Hz to 800 Hz
  • 12-bit and 8-bit digital output
  • I2C digital output interface (operates to 2.25 MHz with 4.7 kΩ pullup)
  • Two programmable interrupt pins for six interrupt sources
  • Three embedded channels of motion detection
  • Orientation (Portrait/Landscape) detection with set hysteresis
  • High Pass Filter Data available real-time
  • Current Consumption: 6 μA – 165 μA

Documents:

SBC8018 AM1808 Single Board Computer

Опубликовано автор admin
  • 375MHz TI AM1808 ARM926 Microprocessor
  • Onboard 128MByte DDR SDRAM + 128MByte NAND Flash
  • UART, USB, Ethernet, LCD/TSP, SATA, Camera, Audio, TF, JTAG,…
  • Optional WiFi, Camera and 3G Modules
  • Ready-to-Run Linux2.6.33 and WinCE 6.0 OS


Hardware Features

Mechanical Parameters

  • Dimensions: 112.24mm x 82.29mm
  • Working temperature: 0~70 Celsius
  • Input Voltage: +5V
  • Humidity Range: 20% ~ 90%
  • Power Consumption: 0.22A @ 5V (working without LCD)

Processor

  • TI AM1808 ARM9 microprocessor
    – 375-MHz ARM926EJ-S RISC MPU, also supports 456MHz operation
    – ARM926EJ-S Core
    – ARM9 Memory Architecture
    – Enhanced Direct-Memory-Access Controller 3 (EDMA3)
    – 128K-Byte On-chip Memory
    – 1.8V or 3.3V LVCMOS IOs (except for USB and DDR2 interfaces)
    – Two External Memory Interfaces
    – Three Configurable 16550 type UART Modules
    – LCD Controller
    – Two Serial Peripheral Interfaces (SPI) Each With Multiple Chip-Selects
    – Two MMC/SD Card Interface with Secure Data I/O (SDIO) Interfaces

Memory

  • 128MByte Mobile DDR SDRAM
  • 128MByte NAND Flash (on the rear of the board)

Audio/Video Interfaces

  • Audio input interface (Mic In)
  • Two-channel Audio output interface (Line Out)
  • Two Camera interfaces (30-pin FPC connector on the rear of the board, supports CCD or CMOS camera)
  • LCD/Touch Screen interface (50-pin FPC connector, support resolution up to 2048*2048)

Data Transfer Interfaces and Other Facilities

  • 1 x 5 line Debug serial port, RS232 voltage (brings out by DB9 connector)
  • 2 x 3 line serial ports, TTL voltage (brings out by extension connector)
  • 1 x USB2.0 OTG port, High-speed (Mini USB type)
  • 1 x USB1.1 Host port, Full-speed (USB-A type)
  • 1 x TF card slot
  • 1 x Serial ATA connector, supports both SATA I (1.5 Gbps) and SATA II (3.0 Gbps)
  • 1 x 10/100Mbps Ethernet interface (RJ45 connector)
  • Battery backed RTC (User needs to prepare battery himself, CR1220 model is ok)
  • 1 x RESET button
  • 1 x BACK button
  • 1 x HOME button
  • 1 x MENU button
  • 1 x 14-pin JTAG connector (for using TI’s XDS100v2 Emulator)
  • 2 x 40-pin extension connectors (SPI, I2C, McBSP, UART, 1.8V, 3.3V, 5V, GPIO are brought out from these connectors)

  • Полное описание
  • SBC8018 (PDF)
  • Купить