Архив рубрики: MQTT

Tasmote MQTT ESP8266 8xRelay Module

Опубликовано автор admin

8-Relay-Tasmota-Ver-1-0-Подключение (PDF)

Schematic_MQTT-Relay-8_2021-04-05

Настройка Tasmota (MCP23017) 16 Input/Output Ports

# Port D0-D7 OUTPUT

backlog sensor29 0,5,0; sensor29 1,5,0; sensor29 2,5,0; sensor29 3,5,0
backlog sensor29 4,5,0; sensor29 5,5,0; sensor29 6,5,0; sensor29 7,5,0

# Port D8-D15 INPUT

backlog sensor29 8,2,1; sensor29 9,2,1; sensor29 10,2,1; sensor29 11,2,1
backlog sensor29 12,2,1; sensor29 13,2,1; sensor29 14,2,1; sensor29 15,2,1

# Enable for binary Sensor

HOME ASSISTANT TIPS:
You can use SetOption59 1 in order to get extra SENSOR status telemetry messages in addition to event-triggered RESULT messages. This allows very good integration with Home Assistant because it needs to monitor only one payload for both periodic and instant messages using.

# Binary Sensor

binary_sensor:
– platform: mqtt
  name: “MCP23017 Test D8 SENSOR”
  state_topic: “tele/tasmota/SENSOR”
  value_template: “{{ value_json[‘MCP230XX’].D8 }}”
  payload_on: “1”
  payload_off: “0”
  availability_topic: “tele/tasmota/LWT”
  payload_available: “Online”
  payload_not_available: “Offline”
  qos: 0
 device_class: door

# Rule – Правила для включения реле при появления сигнала на входах.

rule
on event#MCPINT_D15=1 do power8 on endon on event#MCPINT_D15=0 do power8 off endon
on event#MCPINT_D14=1 do power7 on endon on event#MCPINT_D14=0 do power7 off endon
on event#MCPINT_D13=1 do power6 on endon on event#MCPINT_D13=0 do power6 off endon
on event#MCPINT_D12=1 do power5 on endon on event#MCPINT_D12=0 do power5 off endon
on event#MCPINT_D11=1 do power4 on endon on event#MCPINT_D11=0 do power4 off endon
on event#MCPINT_D10=1 do power3 on endon on event#MCPINT_D10=0 do power3 off endon
on event#MCPINT_D9=1 do power2 on endon on event#MCPINT_D9=0 do power2 off endon
on event#MCPINT_D8=1 do power1 on endon on event#MCPINT_D8=0 do power1 off endon

backlog SetOption36 0;SetOption65 1;wificonfig 4; SetOption59 1

WT32-ETH01

Опубликовано автор admin

Прошивка Tasmota: https://github.com/Jason2866/Tasmota-specials/tree/firmware/firmware/tasmota32

esptool.py –chip esp32 –port /dev/ttyUSB0 –baud 921600 –before default_reset –after hard_reset write_flash -z –flash_mode dout –flash_freq 40m –flash_size detect 0x1000 bootloader_dout_40m.bin 0x8000 partitions.bin 0xe000 boot_app0.bin 0x10000 tasmota32-ethernet.bin

Активировать Ethernet:

backlog template {"NAME":"WT32-ETH01","GPIO":[0,3200,1,3232,1,1,0,0,1,0,1,1,5536,1,5600,0,0,0,0,5568,0,0,0,0,0,0,0,0,1,1,0,1,1,0,0,1],"FLAG":0,"BASE":1}; EthAddress 1; EthType 0; EthClockMode 0; module 0;

Вот еще один модуль.

Описание.

ESP32 with SSD1306 and Tasmota

Опубликовано автор admin

На Заметку: 

  • DisplaySize 1
  • DisplayRows 8
  • DisplayCols 21


backlog displaysize 1; displayrows 8; displaycols 21

Послать текст на экран:

mosquitto_pub -h localhost -u xxx -P xxx -m “DisplayText MQTT” -t “cmnd/ESP32SSD1306/BackLog”

ESP32 с SSD1306 – Если не работает DisplayText – то нужно с начало дать команду

DisplayText [D1]

Выводим температуру ESP32 на экран.

rule1 on tele-ESP32#Temperature do DisplayText [l5c5]Temp: %value% C endon

Передать команду на другое устройство.

publish cmnd/ESP32_SSD1306/DisplayText 123

 

Умный дом контролер Ver 2.0 (Tasmota)

Опубликовано автор admin

Настройка Tasmota (MCP23017) 16 Input/Output Ports

# Port D0-D7 OUTPUT

sensor29 0,5,0
sensor29 1,5,0
sensor29 2,5,0
sensor29 3,5,0
sensor29 4,5,0
sensor29 5,5,0
sensor29 6,5,0
sensor29 7,5,0

# Port D8-D15 INPUT

sensor29 8,2,1
sensor29 9,2,1
sensor29 10,2,1
sensor29 11,2,1
sensor29 12,2,1
sensor29 13,2,1
sensor29 14,2,1
sensor29 15,2,1

# Enable for binary Sensor
SetOption59 1

binary_sensor:
– platform: mqtt
name: “MCP23017 Test D8 SENSOR”
state_topic: “tele/tasmota/SENSOR”
value_template: “{{ value_json[‘MCP230XX’].D8 }}”
payload_on: “1”
payload_off: “0”
availability_topic: “tele/tasmota/LWT”
payload_available: “Online”
payload_not_available: “Offline”
qos: 0
device_class: door

https://tasmota.github.io/docs/MCP230xx/

Схема: Schematic_MQTT-Relay-8_2021-03-02

Rules:

Включить реле при активизации порта D15 и выключить.

rule on event#MCPINT_D15=1 do power8 on endon on event#MCPINT_D15=0 do power8 off endon

Включить и оставить.

rule on event#MCPINT_D15=1 do power8 toggle endon

rule on event#MCPINT_D15=1 do power8 on endon on event#MCPINT_D15=0 do power8 off endon
on event#MCPINT_D14=1 do power7 on endon on event#MCPINT_D14=0 do power7 off endon
on event#MCPINT_D13=1 do power6 on endon on event#MCPINT_D13=0 do power6 off endon
on event#MCPINT_D12=1 do power5 on endon on event#MCPINT_D12=0 do power5 off endon
on event#MCPINT_D11=1 do power4 on endon on event#MCPINT_D11=0 do power4 off endon
on event#MCPINT_D10=1 do power3 on endon on event#MCPINT_D10=0 do power3 off endon
on event#MCPINT_D9=1 do power2 on endon on event#MCPINT_D9=0 do power2 off endon
on event#MCPINT_D8=1 do power1 on endon on event#MCPINT_D8=0 do power1 off endon