RFM23B-868-D

Опубликовано автор admin

Features

  • „Frequency Range = 240–930 MHz „
  • Configurable packet structure
  • „Preamble detector
  • TX and RX 64 byte FIFOs
  • „Low battery detector
  • Temperature sensor and 8-bit ADC
  • „–40 to +85 °C temperature range
  • „Integrated voltage regulators
  • „Frequency hopping capability
  • „FSK, GFSK, and OOK modulation
  • „Power-on-reset (POR)
  • „Sensitivity = –118 dBm
  • +13 dBm Max Output Power
  • Configurable –8 to +13 dBm
  • Low Power Consumption
  • 18.5 mA receive
  • 28 mA @ +13 dBm transmit
  • Data Rate = 1 to 128 kbps
  • Power Supply = 1.8 to 3.6 V
  • Ultra low power shutdown mode
  • Digital RSSI
  • Wake-on-radio
  • Auto-frequency calibration (AFC)

UNIVERSAL ISM BAND FSK TRANSCEIVER MODULE WITH 500mW OUTPUT POWER RFM12BP

Опубликовано автор admin

  • High output power with 500mW
  • Automatic frequency control (AFC)
  • High input sensitivity with -117dBm
  •  Low costing, high performance and price ratio
  • PLL and zero IF technology
  • Fast PLL lock time
  • High resolution PLL with 2.5 KHz step
  • High data rate (up to 115.2 kbps with internal
  • demodulator，with external RC filter highest data rate is 256 kbps)
  • 50 OHM antenna input/output
  • Programmable TX power
  • Data quality detection (DQD)
  • Internal data filtering and clock recovery
  • RX synchron pattern recognition
  • SPI compatible serial control interface
  • Clock and reset signal output for external MCU use
  • 16 bit RX Data FIFO
  • Two 8 bit TX data registers
  • Wakeup timer
  • 2.2V – 3.8V power supply for FSK IC, 12V power
  • Programmable TX frequency deviation (from 15 supply for power amplifier to 240 KHz)
  • Programmable receiver bandwidth (from 67 to 400 kHz)
  • Standby current less than 0.3uA
  • Supports very short packets (down to 3 bytes)
  • Analog and digital signal strength indicator (ARSSI/DRSSI)
Рубрика: ISM

MCB1700 Evaluation Board

Опубликовано автор admin

UM10360

The Keil MCB1700 Evaluation Boards enable you to create and test working programs based on the NXP LPC1700 family of ARM Cortex™-M3 processor-based devices.

The MCB1700 Evaluation Board is available in two different configurations:

  • The MCB1750 Evalution Board is populated with an NXP LPC1758 device
  • The MCB1760 Evaluation Board is populated with a NXP LPC1768 device

Features

  • 100MHz ARM Cortex-M3 processor-based MCU
  • On-Chip Memory: 512KB Flash and 64KB RAM
  • Color QVGA TFT LCD
  • 10/100 Ethernet Port
  • USB 2.0 Full Speed – USB, USB-OTG, and USB Host
  • 2 CAN interfaces
  • 2 Serial Ports
  • SD/MMC Card Interface
  • 5-position Joystick and push-button
  • Analog Voltage Control for ACD Input
  • Amplifier and Speaker
  • Up to 70 GPIO
  • Debug Interface Connectors
    • 20-pin JTAG (0.1 inch connector)
    • 10-pin Cortex debug (0.05 inch connector)
    • 20-pin Cortex debug + ETM Trace (0.05 inch connector)

Bootloading a custom LPC1768 PCB using your mbed!
 

Рубрика: NXP